Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Parts & Welding in Fullerton: What to Know First
We provide independent FAAC gate parts and welding in Fullerton, with most hinge, weld, roller and latch repairs completed in one visit. A typical FAAC gate parts job in Fullerton runs between $180 and $650 depending on what failed and whether we are replacing a hinge, welding a cracked rail, or fabricating a post base. You get an upfront price before any work begins, and every job carries our written 90-Day Done Right Promise.
This page is for Fullerton homeowners whose FAAC gate is sagging, sticking, or refusing to close cleanly. If you have a FAAC swing or slide gate and the problem is structural rather than electronic, you have found the right crew. Call (279) 201-0835 and a live person answers, day or night.
How FAAC Products Fail - and How We Fix Them
- Swing-gate hinge wear on FAAC 400 and 412 operators. FAAC swing operators put repeated stress on the barrel hinges at the gate post. In Fullerton’s dry summers, the hinge pins gall and the gate drops a fraction of an inch. That misalignment makes the FAAC operator work harder and trip its obstruction sensor mid-cycle. We replace the hinges, re-square the gate, and check the operator’s force settings so the motor stops fighting the gate. Two birds, one visit.
- Welded rail cracks on FAAC slide-gate systems. Slide gates using FAAC 844 or 415 operators ride on a steel track. Over years of opening and closing, the track welds or the gate frame’s bottom rail can develop hairline cracks. Water from Fullerton’s winter rains seeps in, rust forms, and the crack spreads until the gate shudders on every pass. We grind out the crack, weld it properly, and reinforce the section so it holds.
- Post movement from soil conditions. Fullerton’s soil expands and contracts through wet and dry seasons. Gate posts set twenty or thirty years ago lean, pulling the FAAC gate out of true. The operator can compensate only so long before the gears in the actuator wear unevenly. We cut and re-weld post bases, or replace the post entirely, then realign the operator mount. It is the difference between replacing a $500 part and a $2,500 operator.
- Latch and lock misalignment on FAAC automated gates. FAAC operators rely on a clean close for the magnetic or mechanical lock to seat. A sagging gate means the latch misses the strike plate by a quarter inch. The operator pushes, the obstruction sensor trips, and the gate reverses. Homeowners often assume the FAAC control board is failing. We check the alignment first, replace the latch or strike, and most times the operator is fine.
- Roller and wheel failure on FAAC cantilever and V-track slides. FAAC slide-gate operators are quiet, which means you hear when a wheel bearing starts to go. A worn roller on the drive side makes the gate wobble and drags the FAAC motor down, tripping thermal protection on hot Fullerton afternoons. We replace wheels and rollers with heavier-duty aftermarket components, not the light-gauge originals, so the next replacement is a decade away.
One thing we see on FAAC gates more than any other brand: the operator is usually fine. The steel around it is what fails. That is why a company with real welding capability matters. If your gate has dropped, cracked, or started scraping, call (279) 201-0835 before the FAAC motor eats itself compensating for it.
Our FAAC Gate Parts & Welding Process
- 1
You call, a person answers. You describe what the gate is doing. We ask about the FAAC model, the gate type, and any recent changes. If it sounds urgent, we can often schedule a same-day or next-day visit in Fullerton.
- 2
We show up and diagnose. Victor Salinas or one of our uniformed technicians inspects the gate structure, the FAAC operator, and the mounting points. We measure for square, check weld integrity, and identify what actually failed.
- 3
We give you a price, not a guess. You get a written, upfront number for the parts and labor. We settle the price before a single bolt is turned. If the gate is too far gone to fix, we will tell you. If it can be fixed right, we will tell you that too.
- 4
We make the repair. That means welding, grinding, replacing hinges or rollers, and realigning the FAAC operator. We use quality aftermarket structural parts where they outperform OEM, and FAAC OEM parts where the manufacturer’s engineering matters, like control boards or gearboxes.
- 5
We test the gate through full cycles. Open, close, obstruction test, force check. A FAAC operator has specific force and sensitivity settings. We verify them against manufacturer specs so the gate closes firmly without becoming a hazard.
- 6
We walk you through it. We show you what we fixed, explain what to watch for, and leave you with the written 90-Day Done Right Promise. Then we clean up and go.
What FAAC Gate Parts & Welding Costs in Fullerton
| Repair Type | Typical Price Range |
|---|---|
| Hinge replacement, swing gate (pair) | $250 to $650 |
| Welding repair, cracked rail or frame | $180 to $450 |
| Latch and strike realignment or replacement | $150 to $400 |
| Post reset or re-weld | $300 to $900 |
| Roller and wheel replacement, slide gate | $225 to $550 |
| Full frame rebuild (severely rusted or sagging gate) | $900 to $2,800 |
The price depends on the weld time, whether the post base is corroded, and how far the FAAC operator needs to be realigned. A hinge replacement on a light single gate is a quick afternoon. A bowed, rusted-out frame that needs three hours of grinding and new steel is a full day. Either way, the price is agreed before we start.
We offer free estimates on FAAC structural work. Call (279) 201-0835 and we’ll take a look and give you a square number.
Why Fullerton Homeowners Call Ironworks Gate Co. for FAAC Work
We have been fixing gates in Fullerton for over 42 years, and a large share of that work is structural. FAAC builds quality operators, but the steel they mount to ages. We are the company that can weld a cracked frame, replace a rotted post, and then set the FAAC operator so it runs like it did the day it was installed.
Every job is backed by our written 90-Day Done Right Promise. No paperwork, no arguing. If it is not right, we come back and make it right. We also carry the standing offer: $50 off any repair over $250, free second opinions on any written estimate, and a $89 seasonal tune-up. A live person answers our phone 24 hours a day, 7 days a week. You will never leave a message and wait until Monday.
And if your FAAC operator itself is failing, we handle it too. We service nine gate-automation brands, including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. Whatever is on your driveway, we have worked on it before.
FAQs
It depends on the part. For electronic components like control boards or gearboxes, we use FAAC OEM parts when the repair calls for it. For structural parts like hinges, rollers, and steel rail, we use aftermarket components that are often heavier-gauge than the factory originals. The welding and fabrication work is done in-house by trained welders, not farmed out.
As an independent FAAC service provider, we cannot speak for FAAC’s warranty terms. But we are careful to protect the operator before any welding begins. We disconnect the operator from its power source, cover the control box, and isolate the actuator so stray current cannot damage the board. Welding on the gate frame while a powered FAAC operator is connected is how boards get fried. We do this work the right way. Call (279) 201-0835 if you have questions about your specific setup.
For broken welds, dropped gates, and hinge failures, we can often get a technician to your Fullerton home the same day or next day. Parts we do not keep on the truck are typically sourced within 24 to 48 hours. If you call us first thing in the morning, the odds are good we are on your driveway by afternoon.
We will tell you straight. If the frame is square, the welds are solid, and the issue is hinges or a roller, repair makes sense. If the gate is rusted through, badly warped, or has been welded before, replacement is often the better use of your money. If we can fix it right, we’ll tell you. If it needs replacing, we’ll tell you that too. You will never get a repair recommendation just to run up a bill. Call (279) 201-0835 for an honest assessment.
We work throughout Fullerton and the surrounding communities, including Brea, Placentia, Anaheim, La Habra, Buena Park, and Yorba Linda. If you are within a reasonable drive of Fullerton, call us and we will schedule it.
Victor Salinas studied welding and metal fabrication at Fullerton College, where he learned the craft from people who had been doing it longer than he had been alive. That foundation has carried through forty years of gate work across Fullerton and the surrounding cities. He still lives within a few miles of where he grew up, not far from Craig Regional Park in the Sunny Hills area. When you call Ironworks Gate Co., you are calling a local company that plans to be here for another forty years.
Call (279) 201-0835 for a free estimate on FAAC gate parts and welding in Fullerton. We price the job before we start it, and we stand behind it when we are done.
Written by Victor Salinas, Owner & Gate Repair Specialist, Ironworks Gate Co. at Ironworks Gate Co., serving Fullerton and nearby areas.