Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Installation in Fullerton: What to Know First
FAAC gate installation in Fullerton typically runs between $1,850 and $5,600 depending on whether you’re automating an existing gate or hanging a new one, with most single-driveway swing jobs landing around $2,400 to $3,800. Labor and parts are quoted upfront and agreed before a single bolt is turned, so the number you hear on the phone is the number on the invoice. We’re an independent FAAC service provider, and we complete most FAAC installations in one visit. If you own a FAAC opener and the gate itself needs to be hung, straightened, or replaced, call (279) 201-0835 and a live person will answer.
How FAAC Products Fail - and How We Fix Them
FAAC builds solid equipment, but after enough Fullerton summers and Santa Ana wind seasons, every brand shows its habits. Here’s what we see on FAAC jobs around town:
- FAAC 400 and 402 operator hydraulic leaks. These residential swing operators run on hydraulics, and the most common failure we find is a slow weep at the release valve or an internal seal that’s hardened after years of heat cycling. The symptom is a gate that starts moving fine but loses force halfway through its travel. We rebuild the hydraulic circuit with fresh seals and correct fluid rather than bolting on a whole new operator, which saves serious money.
- FAAC 391 and 770 control board relay failure. Fullerton’s afternoon heat, especially in neighborhoods like Sunny Hills and Raymond Hills where gates face direct west sun, shortens the life of the board’s relay contacts. The gate will hum but not move, or the board will click repeatedly without engaging the motor. We replace the relay or the board with OEM parts when the gate is under warranty, and quality-compatible boards when it isn’t.
- Gate leaf sag on double swing installations. This isn’t strictly a FAAC problem, but it kills FAAC operators faster than any other issue. When a heavy wrought-iron double gate settles out of square, the operator has to work twice as hard on every cycle, and the motor or pump fails years early. We find this on older Fullerton homes where the original gate was hung on the post without steel reinforcement inside. We weld, shim, and re-hang the leaf before we mount the operator, so the FAAC unit starts its life working with the gate, not against it.
- FAAC 844 and 412 photocell misalignment from soil movement. Fullerton’s clay soil expands and contracts through the wet and dry seasons, and gate posts shift slightly. FAAC safety photocells have a narrow alignment tolerance, and a quarter-inch of post movement triggers a gate that reverses and won’t close. We re-anchor the post or relocate the photocell to a position that holds alignment year-round, then test the full safety cycle.
- Gearbox wear on FAAC 750 and 760 sliding operators. Sliding gates collect fine grit from Fullerton’s decomposed granite landscaping and street runoff. That grit works its way into the gearbox and chews the nylon drive gear, which is designed to be the sacrificial part. You’ll hear a grinding noise on startup. We replace the drive gear, reseal the housing, and set the chain tension correctly so the next gear lasts as long as it should.
Our FAAC Gate Installation Process
A FAAC installation is not guesswork when the person doing it has been working on gates in Fullerton since the 1980s. Here’s what the job looks like from the first call to the final test:
- 1
Call and answer. You call (279) 201-0835. A live person answers, asks about your gate and your FAAC unit, and schedules a visit at a time that works for you.
- 2
On-site measurement and diagnosis. A uniformed, background-checked technician comes to your property, measures the gate leaf, checks the posts, inspects the FAAC operator, and tells you honestly whether the opener can be reused or needs replacement. If we can fix it right, we’ll tell you. If it needs replacing, we’ll tell you that too.
- 3
Written price, agreed before work starts. No surprises. We hand you a written estimate with the labor, parts, and any welding or concrete work broken out in plain language. You approve it before a single bolt is turned.
- 4
Installation. We hang or straighten the gate, mount the FAAC operator, run the power and control wiring, install safety photocells and any keypad or access gear you’ve asked for, and set the open and close limits. Parts come as OEM when the unit is under manufacturer warranty, and proven compatible parts when it isn’t.
- 5
Full cycle test. We cycle the gate a minimum of 20 times, test the safety reverse, check the force settings, and watch for any binding, hesitation, or noise. If something is off, we fix it before we leave, not after.
- 6
Cleanup and written guarantee. We haul away old parts and debris, walk you through the operation and the manual release, and put the 90-Day Done Right Promise in writing. If it is not right, we come back and make it right.
What FAAC Gate Installation Costs in Fullerton
Here’s what we typically see on FAAC jobs in Fullerton, with the understanding that every property is different:
- Automating an existing swing gate with a FAAC 400 operator: $1,850-$2,600
- Automating an existing sliding gate with a FAAC 750 operator: $2,200-$3,400
- New single swing gate with FAAC automation, welded steel frame: $3,200-$4,800
- New double swing gate with FAAC automation, welded steel frame: $4,500-$6,800
- New sliding gate with FAAC automation, steel or aluminum: $4,000-$7,200
The price moves based on gate weight, post condition, the length of the power run from your panel, and whether we need to do any concrete or welding work before mounting the operator. Every estimate is free, and the number we quote is the number you pay. Call (279) 201-0835 and we’ll come out and measure it properly.
Why Fullerton Homeowners Call Ironworks Gate Co. for FAAC Work
We have been working on gates in Fullerton since 1984, and the FAAC units on today’s driveways are the direct descendants of the first hydraulic operators we installed back then. Victor Salinas grew up in the Sunny Hills neighborhood and studied welding at Fullerton College, and the company still runs on the same principle his father taught him: do the work like you’re never going to leave town, because we aren’t.
We carry service knowledge for nine opener brands including FAAC, LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so when you call about a FAAC unit and we find something unexpected, we don’t have to schedule a second visit to figure it out. Most jobs are done in a single trip. Every job is backed by the 90-Day Done Right Promise in writing. And a live person answers the phone 24 hours a day, seven days a week. Call (279) 201-0835 and we will be there when we say.
FAQs
Yes. We regularly mount FAAC operators on existing gates in Fullerton, including older wrought-iron gates that were hung decades ago. The key is checking the post depth, the gate weight, and the hinge condition before mounting the operator. If the gate is in good shape, we install directly. If it needs straightening or welding first, we handle that before the FAAC unit goes on, so the operator is not fighting a worn-out gate from day one. Call (279) 201-0835 for a free on-site look.
Manufacturer warranty on the operator still applies as long as the unit is installed to FAAC’s specifications. That said, we are an independent FAAC service provider, not a factory-authorized dealer, and we are straightforward about that. We install to spec, use the correct settings, and stand behind the labor with our own 90-Day Done Right Promise in writing. If a warranty part fails, we handle the replacement work and deal with the paperwork honestly.
If the operator is under ten years old and the problem is a known component like a control board, seal, or drive gear, repair usually makes more sense. If the unit is older, leaking persistently, or undersized for a heavier new gate, replacement is the smarter money. We will tell you which direction makes sense for your specific FAAC model and your gate’s weight, and the price is agreed before any work begins. Estimates are free at (279) 201-0835.
A straightforward automation of an existing gate is typically done in a single visit lasting four to six hours. A full new gate with FAAC automation, welding, and power work usually takes one full day, sometimes two if we are pouring concrete or running a long power line. We will tell you the timeline when we give you the written estimate, and we hit it.
Yes, both are part of the standard installation. We run the power line from your electrical panel to the operator location, install the FAAC safety photocells, and set up any safety edges the gate requires. The system is tested for full compliance with current safety standards before we leave, including the auto-reverse function, so the gate stops and reverses on obstruction every single time. Call (279) 201-0835 to schedule a free estimate.
If you have a FAAC opener in Fullerton and the gate is worn, sagging, or simply not built for automation yet, call us at (279) 201-0835. We will come out, measure everything properly, and give you a written price before any work starts. No pressure, no surprises, no voicemail. A live person answers.
Written by Victor Salinas, Owner & Gate Repair Specialist, Ironworks Gate Co. at Ironworks Gate Co., serving Fullerton and nearby areas.